A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
The publisher is making several great pointers relating to How to Install a Bathtub in general in this post further down.
Mounting a bathtub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is readily easily accessible, the task can move speedily; if you need to open a wall to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will need an assistant to leave the old bathtub and set in the new one. Make certain you have actually certified on your own for the job as well as fit trying it. As opposed to working with a professional to take control of a halfway-completed task, it is better to consider using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This post will certainly help you install a brand-new bath tub in your washroom if you have already purchased a brand-new tub and also don't need to change the setup of your previous water system pipes.
Your devices and also material list need to comprise the following:
Preparing for the Installation
Firstly, the sustaining frame provided with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps system to stop stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of removing the existing faucets can be fairly problematic due to the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before going on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, position the bathtub in the required setting. The wooden boards are useful in equally spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The next objective is to ensure that the bathtub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub till the spirit level checks out degree.
To mount faucets, fit the bottom of the outermost adaptable tap connector to the suitable supply pipeline by making a compression join; after that do the very same for the various other tap.
Switch on the supply of water as well as check all joints as well as new pipework for leakages and tighten them if necessary. Load the tub as well as additionally check the overflow electrical outlet and also the typical electrical outlet for leaks.
Finally, fix the bath paneling as explained in the supplier's instruction manual. Tiling and also securing around the tub must wait till the bath tub has been made use of a minimum of once as this will certainly resolve it into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to break a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about difficulties with dampness and possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes and cartridges, and also can securing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the bathtub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealant can crack rather very early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently available on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a search on the web. I beg you take a moment to promote this blog entry if you enjoyed it. We love reading our article about How to Install a Bathtub Yourself.
Professional help? Ring! Report this page